Pipe that is staged to accept a muffler.
Either 1 5/16 or 1 1/8.
No Stages (NS)
A pipe with no stages, also includes a weld on muffler adapter.
(Click image for full size image)
(Click image for full size image)
Flat Washer End (W)
Pipe that has a safety washer
welded on the end.
$2.00
Flared Washer End (F)
Pipe that has a flared
(bugle, trumpet) washer welded on the end.
$6.00
(Click image for full size image)
(Click image for full size image)
2 Piece (2P)
This pipe is not welded by us so you can position pipe end where you want it and weld together. It is an easy weld, the pipes slip inside each other by one inch. Can be welded with an acetatelyne torch or 110 V wire welder.
C2 Bend (C2)
Champ kart bend for animal motors.
(Click image for full size image)
(Click image for full size image)
Spring Joint (SJ)
It is made with a slip together joint held together with springs. The end piece can then be strapped right to the frame without breaking the pipe. (See photos below) A joint on a standard pipe is welded together.
$12.95
(Click image for full size image)
(Click image for full size image)
(Click image for full size image)
Head Sleeve (HS)
Can be added to any animal pipe. Sleeve goes down into the port on the head. IKF legal.
$8.50
(Click image for full size image)
(Click image for full size image)
Mounting Kit (K)
A kit that contains basic straps to support pipe back to the motor. Also contains (2) drilled allen bolts, safety wire, and necessary clamps. Long pipes should have more support than the basic mounting kit, like the Cushion Mount (CM). Pieces may vary depending on pipe purchased.
Flathead - $2.95
OHV - $3.95
Muffler Clamp (MC)
Heavy duty extra wide worm gear hose clamp ½ wide. It can be used to hold on a muffler, clamp on flare, or straps. It is much stronger than normal hose clamps.
$4.25
(Click image for full size image)
(Click image for full size image)
RLV Muffler (RLV)
IKF WKA legal mufflers.
X-LARGE
(1 5/16")
$33.50
OPEN X-LARGE
(1 5/16")
$36.50
Clamp on Flare (COF)
A staged flared end that can be clamped or welded to the end of a muffler end pipe. It is the same length as a standard RLV muffler.
$15.95
(Click image for full size image)
(Click image for full size image)
Cushion Mount (CM)
2 rubber mounts between adjustable straps with holes and slots. It can be clamped or bolted to pipe and frame. It is the best way to support the end of a long pipe and muffler.
$7.95
(Click image for full size image)
(Click image for full size image)
(Click image for full size image)
(Click image for full size image)
COLLECTOR
This is a 2 into 1 collector.
It measures 1 1/8 or 1 ¼ in and 2” out.
Made for V-Twin motors.
$26.95
PIPE BENDS
Build your own pipe.
Available in .902, 1.025, or 1.150 ID.
All staged at one end for slip together fit.
U bend - $7.95
45° bend - $6.95
90° bend - $6.95
(Click image for full size image)
FLANGES
$6.00
DRILLED ALLEN BOLTS
Packets of 10 with 5 feet of safety wire
BRIGGS (1/4")
$5.20
TECUMSEH STAR (5/16")
$6.20
ANIMAL (6MM X 20MM)
$6.50
HONDA (8MM X 20MM)
$6.50
Tecumseh Air Filter Adapter
Air filter adapter for most Tecumseh model engines. OHV 5.5 - 6.5 HP motor shown in picture. The center to center on flange bolts holes measurement is 1 11/64". It is 2 1/4" tall. You can put on a 1 5/16" clamp on filter.
